JAWUG

Output from the dead GNA16B Access Point

display on
entering boot loader, turning on display
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
Linux version 2.4.18-MIPS-01.00 (root@betty_linux) (gcc version 3.0.3) #276 ¶g¤T
 8¤ë 18 17:08:42 CST 2004
Determined physical RAM map:
 memory: 00800000 @ 00000000 (usable)
Initial ramdisk at: 0x80170000 (357407 bytes)
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 204.80 BogoMIPS
Memory: 6104k/8192k available (1328k kernel code, 2088k reserved, 432k data, 44k
 init, 0k highmem)
Dentry-cache hash table entries: 1 (order: 1, 8192 bytes)
Inode-cache hash table entries: 512 (order: 0, 4096 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 1 (order: 0, 4096 bytes)
 unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
LED & GPIO Driver 111v1.0
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 1700K size 1024 blocksize
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
NET4: Ethernet Bridge 008 for NET4.0
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: bzip2 compressed image found at block 0
Freeing initrd memory: 349k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 44k freed
mount /proc file system ok!
serial console detected.  Disabling virtual terminals.
console=/dev/ttyS0
init started:  BusyBox v0.60.1 (2004.08.18-08:28+0000) multi-call binary


BusyBox v0.60.1 (2004.08.18-08:28+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

Initialize WLAN interface
length=0?
killalldo_page_fault() #2: sending SIGSEGV to killall for illegal write access t
o
: iapp: 00000000 (epc == 00432974, ra == 00432940)
no process killedSIGSEGV
killalldo_page_fault() #2: sending SIGSEGV to killall for illegal write access t
o
: auth: 00000000 (epc == 00432974, ra == 00432940)
no process killedSIGSEGV
killalldo_page_fault() #2: sending SIGSEGV to killall for illegal write access t
o
: iwcont00000000 (epc == 00432974, ra == 00432940)
rol: no process killedSIGSEGV
length=0?
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist!
bridge br0 doesn't exist; can't delete it
Setup bridge...
Algorithmics/MIPS FPU Emulator v1.5
device eth1 entered promiscuous mode
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
This is 8201BL
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
eth1: Promiscuous mode enabled.
SIOCDELRT: No such process
br0: port 2(wlan0) entering listening state
br0: port 1(eth1) entering listening state
br0: port 2(wlan0) entering learning state
br0: port 2(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth1) entering learning state
br0: port 1(eth1) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
iappauth.sh: not found
********** run Diagd **********
do_page_fault() #2: sending SIGSEGV to killall for illegal write access to
00000000 (epc == 00432974, ra == 00432940)
SIGSEGV
setting: port: 31727
running in daemon mode
********** run GaTest **********
332
333






























         Please enter your Name and Password



 User Name   :











-------------------------------------------------------------------------------
<TAB> Select                     <ESC> Exit                     <Enter> Enter